Question 1

Which of the following is not a common ABS configuration?

Accepted Answer

A)  Rear wheel antilock
B)  Four wheel antilock
C)  Front wheel antilock
D)  Three wheel antilockE) B) and D)
F) None of the above

Question 2

Which of the following tools can be used to check AC voltage-generating wheel speed sensors?

Accepted Answer

A)  Oscilloscope
B)  Scan tool
C)  Digital multimeter
D)  All of the aboveE) All of the above
F) A) and D)

Question 3

ABS units that combine functions of the master cylinder, ABS control, and power assist are called ........systems.

Accepted Answer

The answer of ABS units that combine functions of the...

Question 4

Vehicles with stability control use a multiple ........to determine vehicle movement.

Accepted Answer

sensors

Question 5

If a wheel locks during braking, wheel speed sensor data will show a ........in the number of rotations for the wheel.

Accepted Answer

The answer of If a wheel locks during braking, wheel...

Question 6

All of the following are modes of ABS operation except:

Accepted Answer

A)  Pressure increase mode
B)  Release mode
C)  Hold mode
D)  Calibration modeE) B) and C)
F) B) and D)

Question 7

A vehicle has illuminated red BRAKE and yellow ABS lights: Technician A says a thorough inspection of the brake system should be performed.Technician B says to check for store DTCs.Who is correct?

Accepted Answer

A)  Technician A
B)  Technician B
C)  Both A and B
D)  Neither A nor BE) B) and C)
F) A) and D)

Question 8

Traction control systems are designed to reduce ........to slipping drive wheels.

Accepted Answer

torque

Question 9

Two technicians are discussing bleeding the hydraulic brake system on an ABS-equipped vehicle: Technician A says special bleeding procedures may be required purge all of the air from the system.Technician B says some antilock systems require using a scan tool to bleed the system.Who is correct?

Accepted Answer

A)  Technician A
B)  Technician B
C)  Both A and B
D)  Neither A nor BE) All of the above
F) A) and B)

Question 10

A vacuum ........is used to keep a reservoir of vacuum in the power brake booster in the event the engine stops running.

Accepted Answer

check valve

Exam 16: Antilock Brakes, Vehicle Stability Control, and Power Assist

Which of the following is not a common ABS configuration?

Correct Answer
verified

Which of the following tools can be used to check AC voltage-generating wheel speed sensors?

Correct Answer
verified

ABS units that combine functions of the master cylinder, ABS control, and power assist are called ........systems.

Correct Answer
verified

Vehicles with stability control use a multiple ........to determine vehicle movement.

Correct Answer
verified
sensors

If a wheel locks during braking, wheel speed sensor data will show a ........in the number of rotations for the wheel.

Correct Answer
verified

All of the following are modes of ABS operation except:

Correct Answer
verified

A vehicle has illuminated red BRAKE and yellow ABS lights: Technician A says a thorough inspection of the brake system should be performed.Technician B says to check for store DTCs.Who is correct?

Correct Answer
verified

Traction control systems are designed to reduce ........to slipping drive wheels.

Correct Answer
verified
torque

Two technicians are discussing bleeding the hydraulic brake system on an ABS-equipped vehicle: Technician A says special bleeding procedures may be required purge all of the air from the system.Technician B says some antilock systems require using a scan tool to bleed the system.Who is correct?

Correct Answer
verified

A vacuum ........is used to keep a reservoir of vacuum in the power brake booster in the event the engine stops running.

Correct Answer
verified
check valve

Exam 16: Antilock Brakes, Vehicle Stability Control, and Power Assist

Which of the following is not a common ABS configuration?

Correct AnswerverifiedShow Answer

Which of the following tools can be used to check AC voltage-generating wheel speed sensors?

Correct AnswerverifiedShow Answer

ABS units that combine functions of the master cylinder, ABS control, and power assist are called ........systems.

Correct AnswerverifiedShow Answer

Vehicles with stability control use a multiple ........to determine vehicle movement.

Correct Answerverifiedsensors

If a wheel locks during braking, wheel speed sensor data will show a ........in the number of rotations for the wheel.

Correct AnswerverifiedShow Answer

All of the following are modes of ABS operation except:

Correct AnswerverifiedShow Answer

A vehicle has illuminated red BRAKE and yellow ABS lights: Technician A says a thorough inspection of the brake system should be performed.Technician B says to check for store DTCs.Who is correct?

Correct AnswerverifiedShow Answer

Traction control systems are designed to reduce ........to slipping drive wheels.

Correct Answerverifiedtorque

Two technicians are discussing bleeding the hydraulic brake system on an ABS-equipped vehicle: Technician A says special bleeding procedures may be required purge all of the air from the system.Technician B says some antilock systems require using a scan tool to bleed the system.Who is correct?

Correct AnswerverifiedShow Answer

A vacuum ........is used to keep a reservoir of vacuum in the power brake booster in the event the engine stops running.

Correct Answerverifiedcheck valve

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
sensors

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
torque

Correct Answer
verified

Correct Answer
verified
check valve